Electric Swing Gate Kits
Choose an electric swing gate kit for a single hinged gate or a pair. Start with the number of gate leaves, then use the size and weight of each leaf, the hinge and post layout and the available space to narrow the choice. These kits provide automation equipment rather than the gate leaves themselves.
Browse above-ground kits below or see our underground swing gate kits for a more discreet installation. If you already know the brand or model, use it to find the relevant options. Does your gate travel sideways? Go to sliding gate automation instead.
Explore subcategories
How to choose a swing gate automation kit
Start with a single or double gate
Measure the width and estimate the weight of each moving leaf. For double gates, record both leaves separately because they may not be the same size. The kit description should also tell you whether it contains one operator or a pair, together with the controls and accessories supplied.
Which operator style suits your gate?
- Linear arms: a common above-ground choice. The hinge position, mounting dimensions and clearance beside the open gate all need to match the operator drawing.
- Articulated arms: often considered where the hinge is set back on a deeper post. Allow room for the arm to move and use the dimensions for the exact model.
- Underground operators: keep the drive below ground. Selection includes the hinge layout, foundation boxes, drainage and access for installation and maintenance. Our underground-kit guide covers this route in more detail.
Post depth can change the options considerably. For example, CAME publishes a C-dimension limit and model-specific operating limits for its ATS range. If your hinges are set well back from the face of the post, our hinge and post geometry guide shows the measurements to send us.
What about a small driveway or outward-opening gates?
Allow for both the sweep of the gate leaf and the space used by the operator. Note the opening direction, required angle, nearby walls, parked vehicles and any slope across the entrance. Outward opening and unusually wide angles need an operator and mounting arrangement designed for that layout; 180-degree opening is model-specific.
How much weight and gate length can the motor handle?
Use the manufacturer's weight and leaf-length figures to build a shortlist, then compare the full operating limits and mounting drawing. Gate construction matters too: an open five-bar gate behaves differently in the wind from a solid timber or close-boarded metal gate of a similar weight. Include the site's wind exposure and expected number of daily operations when asking us to help specify the equipment.
Should I choose 24 V or 230 V?
The motor voltage and the incoming supply for the complete control system are separate specifications. Many 24 V motors still form part of a mains-powered system, with battery backup available only where the chosen controls support it. Compare the operator, control panel, expected use and backup requirements together.
How fast will the gate open?
Opening times vary by the exact operator version, gate geometry and the conditions used for the published figure. If speed matters, tell us what you want to achieve so the motor, controller and mounting arrangement can be considered as a complete system. Safe operation and suitability for the gate remain the priority.
Can I automate my existing gates?
Usually the first step is to assess the gates as they stand. Send photographs, the dimensions and approximate weight of each leaf, hinge and post measurements, the required opening direction and angle, and any existing equipment references. The gates should move freely and be in suitable condition before automation is specified; retained controls and accessories also need to be checked with the proposed operator.
What comes in a swing gate kit?
Kit contents vary, so read the list for the exact package. Compare the operators, control equipment, remotes, mounting parts and accessories supplied, then allow for any required foundation boxes, manual releases, protective equipment or supported battery backup. Add an access keypad or intercom system separately where it is not listed in the kit. The prices shown cover equipment rather than gate leaves, installation or a complete on-site project.
What safety equipment will the finished gate need?
Built-in obstacle detection is one part of the finished system. HSE's powered-gate guidance explains that safety depends on how the gate, motor, controller and protective devices work together at the particular site. The installation needs an appropriate risk assessment, correct commissioning and ongoing maintenance.
Looking for a replacement motor?
Replacing one motor? Use the full code, voltage and control-panel details from the existing operator. A "heavy-duty" label alone won't tell you whether an operator fits your gate: leaf length and weight, hinge geometry, wind exposure and expected use all matter.
Browse replacement gate motors and operators for a complete drive, or gate automation spares for an identified component. If the reference is hard to read, send us clear photographs of accessible labels and we can help identify the right part.
For a new project, or whenever the layout is uncertain, complete our gate automation survey form and we will help specify the equipment. Metalines supplies and specifies equipment; we do not provide installation, site visits or on-site repairs.













